DAL 1457 emergency about to land in ATL
#31
In addition to the points made by others:
1. You normally would not want to retract landing gear after a tire failure -- the old saying goes, "A down gear is a happy gear"
2. You normally would not want to retract the flaps after a tire failure since some of the rubber could have been thrown into the flap mechanism, causing potential damage or jamming, and finally,
3. Due to the above stated reasons, they would not have had sufficient fuel anyway for a flight from ATL to Portland with gear and flaps extended.
I don't know what flap setting they landed with, but I suspect they extended the flaps incrementally to minimize control issues in the event that any flaps were damaged or jammed.
1. You normally would not want to retract landing gear after a tire failure -- the old saying goes, "A down gear is a happy gear"

2. You normally would not want to retract the flaps after a tire failure since some of the rubber could have been thrown into the flap mechanism, causing potential damage or jamming, and finally,
3. Due to the above stated reasons, they would not have had sufficient fuel anyway for a flight from ATL to Portland with gear and flaps extended.
I don't know what flap setting they landed with, but I suspect they extended the flaps incrementally to minimize control issues in the event that any flaps were damaged or jammed.
The 737NG does not use gear doors. The tires fit very tightly in the gear wells to reduce drag. Any damage to the tire could jam the gear in the well. To prevent this there is a pin that would be hit by a blown or damage tire. It prevents that gear from retracting into the gear well and it free falls back down. It would be a long flight to PDX with one gear hanging down.
Thanks for your reply.
Obviously as a novios there are critical elements and technicalities that we (I) are not completely skilled to decipher.
Well, concerning this question .... now I am.
THX
#32
Moderator
Joined: Dec 2007
Posts: 7,249
Likes: 94
From: DAL 330
The 737NG does not use gear doors. The tires fit very tightly in the gear wells to reduce drag. Any damage to the tire could jam the gear in the well. To prevent this there is a pin that would be hit by a blown or damage tire. It prevents that gear from retracting into the gear well and it free falls back down. It would be a long flight to PDX with one gear hanging down.
My dear man - you must be a 777 pilot, or something similarly impressive - but surely not a lowly 737 pilot. The pin as you so cavalierly called it, is actually a "frangible fitting" which protrudes next to where the gear retracts. Theory being, a damaged tire will break the fitting, which will bleed out hydraulic fluid, causing the gear to free-fall, if it where indeed, in the retraction process. If the gear was down - same result, you cannot raise it, due to no hydraulic fluid in the "gear-up" lines.
Scoop - Lowly 737 Pilot
#33
Gets Weekends Off
Joined: Feb 2006
Posts: 973
Likes: 0
From: A320 CA
I heard from a friend of a training Captain who said on the 320 if you blow a tire the computers will over-rule the pilot and prevent him from exceeding a 75 mile radius of the departure airport
#34
Gets Weekends Off
Joined: Feb 2008
Posts: 20,866
Likes: 178
Sailing, Sailing, Sailing,
My dear man - you must be a 777 pilot, or something similarly impressive - but surely not a lowly 737 pilot. The pin as you so cavalierly called it, is actually a "frangible fitting" which protrudes next to where the gear retracts. Theory being, a damaged tire will break the fitting, which will bleed out hydraulic fluid, causing the gear to free-fall, if it where indeed, in the retraction process. If the gear was down - same result, you cannot raise it, due to no hydraulic fluid in the "gear-up" lines.
Scoop - Lowly 737 Pilot
My dear man - you must be a 777 pilot, or something similarly impressive - but surely not a lowly 737 pilot. The pin as you so cavalierly called it, is actually a "frangible fitting" which protrudes next to where the gear retracts. Theory being, a damaged tire will break the fitting, which will bleed out hydraulic fluid, causing the gear to free-fall, if it where indeed, in the retraction process. If the gear was down - same result, you cannot raise it, due to no hydraulic fluid in the "gear-up" lines.
Scoop - Lowly 737 Pilot

"""This pin is designed to detect any loose tire tread during gear retraction. If any object impacts on it during retraction, then the gear will automatically extend. The affected gear cannot be retracted until this fitting is replaced. There is one pin at the aft outside of each main wheel well.
I know its a frangible fitting however the point is that a gear with tire damage can not be retracted on the 737NG series. I never flew the earlier versions so have no idea about what they have.
#36
Its actually 75KM but there is an +/- factor in the limit. At 78.5KM the autoflight takes over and announces, "Je l'ai vous imbécile stupide. Je suis le capitaine maintenant and je débarquerai l'avion." which roughly translates to "I have it you stupid imbecile. I am the captain now and I will land the airplane."
#37
Its actually 75KM but there is an +/- factor in the limit. At 78.5KM the autoflight takes over and announces, "Je l'ai vous imbécile stupide. Je suis le capitaine maintenant and je débarquerai l'avion." which roughly translates to "I have it you stupid imbecile. I am the captain now and I will land the airplane."

GJ
#38
(at least that sounds a lot better than 'we were engrossed in a computer scheduling program.' RIGHT...)
#39
Gets Weekends Off
Joined: Aug 2008
Posts: 127
Likes: 0
#40
The actual overfly event would then trigger the existing auto thrust landing voice prompt "Retard, Retard".

SP
Thread
Thread Starter
Forum
Replies
Last Post



